Chris Randall: Musician, Writer, User Interface Designer, Inventor, Photographer, Complainer. Not necessarily in that order.
April 6, 2018
by Chris Randall
Audio Damage will once again have a booth at Superbooth this year, and I'm leaving for Berlin on April 27. That means I have about 3 weeks to finalize everything. The product we're unveiling is in feature-freeze, and it's time to start figuring out how to demonstrate it, as well as the rest of our product line. (This isn't a last-minute thing; I've been thinking about it for some time.)
The entire process is both easier than years past, and more complicated. At the last two Superbooths we attended, we only showed Eurorack, and didn't show our software products at all. This year, it will be the other way around. We have no Eurorack; we're showing our desktop and iOS software. The iOS part is easy; a 12.9" iPad Pro with the usual dongling, job done. For the desktop software, the needs were somewhat odder. The product we'll be unveiling is MPE-capable, so we wanted to have at least one MPE controller at our booth. Since the iOS and desktop versions are identical in that regard, it seemed wise to have one MPE-capable controller for each, and of those, at least one that civilians could play. Roli very generously loaned us a Rise 25 for the booth, so that will attach to the iPad, and my Linnstrument will go as well, for the desktop stuff.
All but a couple of our products are now vector-graphics and HiDpi-capable, so I wanted a 4K monitor to show this off. My own monitor is too big, so I purchased a Dell 23" 4K for the show. Now the trouble starts. You would think it would be a fairly simple matter to sling a computer at this problem and be done with it. You'd be wrong. The software we're unveiling is nearing completion, but it is in no way finished, so it isn't as optimized as we'd like. I don't want to use my main work laptop for a trade show, for obvious reasons, so I pulled out a mid-2013 MacBook Pro, and between pushing a 4K monitor and this fairly heavy-duty plugin, it was screaming for baby Jesus. So, we decided to run Windows instead of OSX for the booth. That being the case, we needed a Windows machine capable of both fairly heavy lifting in the graphics department while shouldering the CPU burden of a DAW. Plus, we have a fairly thin budget and weight considerations. It was a surprisingly tough nut to crack.
After a whole lot of reading of computer gear blogs and fretting, I decided that I had enough time to take a small risk, and I ordered up one of the new Intel Skull Canyon NUCs. As it is a bare-bones system, containing only a CPU/GPU, I also grabbed 16GB of RAM, an NVMe drive, and a key for Windows Home 10 64-bit. All of that showed up this morning.
I'll admit that while I knew intellectually how small the Skull Canyon NUC was, I was unprepared for the reality of it. It is just about the same size as a VHS tape. The power brick is almost as big as the computer itself. Anyhoo, it comes with a pretty good selection of ports (including, improbably, a Thunderbolt 3 port, if you want to run a graphics card in a chassis, or a UAD Apollo or whatever.) It took me about 30 minutes in all to set it up, from opening the boxes to signing in to Windows, after I installed Windows off a USB drive built with Windows Media Creator on my big machine.
We'll be using Bitwig Studio 2 to demonstrate our products at Superbooth (for two reasons: a native understanding of MPE, and a good HiDpi implementation on Windows), so I popped over to the Bitwig site and slammed that on the machine, as well as a few of our plugs and some samples. I've been pressure-testing it for several hours now, and I have to say that, taking its size in to account, this computer is an amazing value. I wouldn't use it as my main workstation, but for situations like this, or for a secondary machine or media center, it is fucking amazeballs. With the caveat that I still have a lot to do before I'll call it Show Ready™, I'm of the opinion that this is a solid machine for the money. Two thumbs tentatively up.